Results 1 to 5 of 5

Thread: Flash and SAMSC

  1. #1

    Flash and SAMSC

    To control SAMSC via FLASH...
    Make a file that has buttons in it with the following action script...

    on (release) {getURL("http://10.0.2.62/samsc(cuelist,searchandplay,Ver)");}

    Note:VER is the cue label in SAMSC.
    This script will send a request to SAMSC to play the cue labeled VER. You will want to use other labels and this is where you would change Ver to you own label.
    Do not use numbers. They do not work.

    Export your flash file as a movie/flash file.
    load it into a SAMSC quicktime device player. And your off.
    The best way is to make your document the same size as your video/monitor resolution and then take the file into full screen mode and now you have an interface for an installation application.

    Caps Do Matter in your names

    see ya,
    Tim Grivas
    Last edited by timgrivas; 08-02-2006 at 10:52 PM.

  2. #2
    could the same be done regarding controlling catalyst??
    With my best regards

    Thomas Rotten


    My toy...

    The Fastest Catalyst system in denmark..

    Mac Pro 8 core
    4 GB Ram
    4 TB S-ATA Raid
    Catalyst Express v. 4.10
    Elc dmxLAN mode 3 with 1 input and 2 pixelmad output
    All integrated in flightcase with 2 15" lcd monitors..

  3. #3
    Yes.

    Look at the documentation for Catalyst regarding the http commands. This is already possible in Catalyst. You can use Flash or even write some basic html to remotely trigger cues.
    SourceChild
    TODD SCRUTCHFIELD

    ...if it ain't broke...
    gimme 5 and then don't act surprised

  4. #4
    thanks...

    I though i hade looked everywere in the manual but now i found the little extra manual( whats new in catalyst ) and i´m happy again. (i hope) Thanks
    With my best regards

    Thomas Rotten


    My toy...

    The Fastest Catalyst system in denmark..

    Mac Pro 8 core
    4 GB Ram
    4 TB S-ATA Raid
    Catalyst Express v. 4.10
    Elc dmxLAN mode 3 with 1 input and 2 pixelmad output
    All integrated in flightcase with 2 15" lcd monitors..

  5. #5
    YES!!!! its working. I can trigger a cuelist to start, I can stop them again one at the time but i can not get the command

    http://myip:8080/commands/?StopAllCueLists

    to work??

    very very strange...

    So what i have done so far is making a script to trigger preset 1 at catalyst startup. This preset starts a background movie up on layer 1 in loopmode.
    Then by a simple fullscreen flash file i have 10 buttons each triggering a cuelist saying play movie on layer 2, fade in in 1 sec. then a fade out on the time when the movie is finish.

    btw
    is it just me or is there a little error in the diagram on page 38 in the manual.

    I use
    http://myio:8080/commands/?StartPlayCueListNumber=0.0 to start cuelist 0.0

    and
    http://myio:8080/commands/?StopPlayCueListNumber=0.0 to stop cuelist 0.0
    Last edited by thomasrotten; 10-03-2009 at 11:00 AM. Reason: i just forgot
    With my best regards

    Thomas Rotten


    My toy...

    The Fastest Catalyst system in denmark..

    Mac Pro 8 core
    4 GB Ram
    4 TB S-ATA Raid
    Catalyst Express v. 4.10
    Elc dmxLAN mode 3 with 1 input and 2 pixelmad output
    All integrated in flightcase with 2 15" lcd monitors..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •