working configuration of catalyst server, need tip

[samsc]

your content:

from your pdf - you convert most things to AIC - and most files are normal SD resolutions 720x480 etc

dont convert using catalyst - it doesnt work with h264/mpeg type codecs - and doesnt do frame rate conversions

use one of the batch convertors out there like apples compressor - or episode - or others

use apple prores codecs - not AIC

there are 5 different ones

proxy - faster than AIC
LT - about same as AIC
422 - slower than AIC
422HQ - high quality - much slower than AIC
4444 - super high quality - much much slower than AIC

prores codecs dont use any interframe compression like h264 - and work very well -
https://www.apple.com/final-cut-pro/...hite_Paper.pdf

[faceoff]

thanks for tips, staying, from now I will convert all in proress codec, but still a problem with crash when doing periodically a - s - a actions.

And what means color bars in stats hud in stats1 tab near draw mp etc. red green and violet (sometimes violet bar goes to 100% and all freeze for a 5-10 seconds.)

Also sometimes when trying to save all preference now it would hang on colors stage...

[samsc]

please do pdf profile in catalyst -
your problems may be unique to your specific system -
and not seen or reported by anyone else - this is very often the case

and run etrecheck - to see what stuff you got installed
http://etresoft.com/etrecheck

[faceoff]

send both via dropbox

[samsc]

you using mac OS x- very close to initial release of the mac pro 6.1 - 10.9.2 - you not upgrade to last one -10.9.5?

you have firewall in mac os turned on?
thats your network connection issue-

your hp display is using the display port connection - and not responding with any screen EDID- and no valid screen refresh values - ( your catalyst crash at startup was when screen reported no EDID ) - it have a dvi port?

the catalyst safenet dongle driver is crashing all the time- not my software - but 3rd party

try installing latest version-
http://sentinelcustomer.safenet-inc....HL&o=all&t=all
Sentinel HASP/LDK Mac OS X Run-time GUI Installation

-

you mixing display port with dvi-
x4 at 3840x2160 30Hz - with 2560x1600 unknownHz
you not try to use all same outputs at 1920x1080@50Hz ?- i thought this was your show requirement?

like i suggested before? so you get 25/50 on all outputs all at same size and refresh?

i do not believe the x4 can do correct EDID and refresh for exact frequencies at this resolution at either 25Hz or 30Hz

[faceoff]

Trully version of mac os is 10.10.2 for now. When install hasp driver used the last one at site but I check if it updated. HP work on 2560*1600@60Hz and in logs tab it discovered properly. I cannot use now dvi because I haven't second converter from mini DP to dual dvi. I use datapath with 4k resolution, because I need 4 separate full HD output, and I have it with 50Hz, as I say earlier datapath can set for each output any refresh rate. (and for trying to test n541 with 5 output I need 5 miniDP - Dual Link DVI wires and usb power hub for this reason, otherwise it wouldn't work)

[samsc]

Trully version of mac os is 10.10.2 for now. When install hasp driver used the last one at site but I check if it updated. HP work on 2560*1600@60Hz and in logs tab it discovered properly. I cannot use now dvi because I haven't second converter from mini DP to dual dvi. I use datapath with 4k resolution, because I need 4 separate full HD output, and I have it with 50Hz, as I say earlier datapath can set for each output any refresh rate. (and for trying to test n541 with 5 output I need 5 miniDP - Dual Link DVI wires and usb power hub for this reason, otherwise it wouldn't work)

please install 10.9.5 - do updates for 10.9.2


if you want 4 ( or 5 or 6 ) separate 50hz outputs:
use startech unpowered active adaptors mini display port to dvi- no usb power required - usb power only required for dual link
1080p50 ( and 1080p60 ) is single link for dvi
MDP2DVIMM6BS
http://www.amazon.co.uk/Startech-Dis...i+display+port
there are different colors sexes and lengths