Having problems with Triple Head to Go

[ILCstaff]

With my triple head to go, I have 4 screens. The center two are a panorama, I am having trouble getting rid of the seams where the two images meet.

Here is what I am using: 1x Cat 4.06, 1x triple head to go, 4x 5k projectors,

My show is this Monday 3/19

[samsc]

have you ever tried this sort of thing before?

what settings are you using?

what is your projection geometry like?

[ILCstaff]

have you ever tried this sort of thing before?

what settings are you using?

what is your projection geometry like?

I tried it when it was still in beta and could not get rid of the seam.

What setting do you need to know.

My projectors are RP with a straight shot.

[samsc]

I tried it when it was still in beta and could not get rid of the seam.

What setting do you need to know.

My projectors are RP with a straight shot.

settings? all of them that relate to what you are trying to do

have you done this before? ( with any equipment not necessarily with catalyst )

Do you understand what this does?

Flat screens or curved?

There are many many many things with doing this stuff.

What do you see?

[ILCstaff]

settings? all of them that relate to what you are trying to do

have you done this before? ( with any equipment not necessarily with catalyst )

Do you understand what this does?

Flat screens or curved?

There are many many many things with doing this stuff.

What do you see?

--------------------------------------------------------------------------

I tried to image blend last back in January with the beta version and couldn't get it set up right. More than likely operator error.

Right now I am trying to do a mock up, I do not load in till Sunday. I have a through of 18' 6". I am Rear Projection onto flat screen. 4 projectors total. Two outside do not blend. The two inside are blended to make a 10'x 30' panorama.

I have my blend set at 10%. With the blending HUD, I lined up the magenta bars so they are close, but I am having a hard time getting them dead on.

I have my two mixes set so that layer 1 is active on both screens.

My images do not meet correctly. If I move my mixes so that they match up at the screen, then the blend is bad.

[samsc]

try a bigger blend for a start - 15% or 20%

[samsc]

What is the black level light output from the projectors?

Feed them a black input signal - dont need catalyst, and overlap the projectors outputs, what do you see?

This gives you an indication of the black level leak.

If this is noticeable - you might have a hard time.

Are your projectors DLP or LCD?

[Mick Murray]

I bought two th2g's as well hoping i'd be able to run 6 screens, i was not!
I have a quad core intel mac with a xt1900 video card, it runs 3 outputs fine on one th2g 3072 x 768 but when the 2nd th2g goes on there i cannot select a th2g see the th2g resolution for that output. I tried running the first th2g at a much lower res but didn't make a difference, does anyone have a graphics card they can suggest that would make this all work?

p.s.
They are analogue th2g's

[emilianomorgia]

I bought two th2g's as well hoping i'd be able to run 6 screens, i was not!
I have a quad core intel mac with a xt1900 video card, it runs 3 outputs fine on one th2g 3072 x 768 but when the 2nd th2g goes on there i cannot select a th2g see the th2g resolution for that output. I tried running the first th2g at a much lower res but didn't make a difference, does anyone have a graphics card they can suggest that would make this all work?

p.s.
They are analogue th2g's

strange .... i'm in a show right now using two triple for a total of 6 800x600

It worked fine on tiger and leo booth 2,66 and 3 giga I've tried this with many system configuration it always worked good ...

can you connect your mac pro to internet ?

do you have an ichat account ?

Can you post the system profile ?

[Mick Murray]

Am in japan with show at mo, will try it again when i get back, what software version are you running?