very much! thank u nev....do we get to see ur handy work on eurovision this year?!
Printable View
very much! thank u nev....do we get to see ur handy work on eurovision this year?!
I finally had some time to try out the new version. i really like the frame blending, works nice and easy, my first impression is that the frame blend is smother and looks better than the Hippo frame blending i will do an AB test and compare it to the Hippos frame blending. I just played around whit the new color FX and it really looks promising. I think i experienced increased performance but just upgraded my machines to OS X 10.6 at the same time, so it can be just the OS X.
Thanks for some sweet new software!
No problem.
I have no idea if we will be involved in the Eurovision this year. It all depends on which lighting designer is chosen and the hire companies!!
Fingers crossed!!!
Nev.
Is there a fixture Update to add all the new play modes to the Road Hog Full Boar. I can only find 2 of the audio play modes and I know there are more now.
RHFB 3.1.7
*nevermind- it takes two buttons*
Ryan
Thats a question for High End I think!
Nev.
I asked Steve to update the lib.
In the webserver I cant find the DMX Values for those new modes
Any idea where to look or where I can find an actual DMX Chart?
Hi Richard,
I am working with Catalyst m329 in GrandMA console, I created some libraries to work with Mix Type, etc.
I am having the following problem, I pass in more parameters but I put this as an example.
MIX Type
Ch6 MIX Screen Left - 16 bit
NO Change 0
Position 1 to 30000.
It often happens that if we have the Encoder in coarse mode and spent a 1, 2 etc and returning to 0 (1 step in coarse encoder 256 steps in fine) is not well reflected the movement, since a value 0 corresponds to no change .
Thus the mix is half display when they should be left completely.
This happens with all the parameters that have values of 0 and NO change.
Any suggestions?
Thanks
E. Cueto
its absolutely essential to have a 'no change value'
otherwise you the poor end user -
have to program every single value to do something - to be a default- even when you dont need it-
you might just want to set one value in the mix setup -
but without a no change - you cant do this
Update on lib for the HOG3.
I mailed Highend all infos, they will have an update ready in the next days.
hi all
control through the window of catalyst mixer, I can get negative values for Screen 1 and 2, TOP, LEFT, but since arnet NOT possible?
Mix Type, channels 4,6, 12 and 14.
A greeting
E. Cueto
Hi there
not sure why you need to move the mix off of the screen? If you need to move content off, just use the Offset value instead?
Nev.
I'm working on the libraries for Ma
It was just a technical question.
thanks
I used it in touring situations, 4 LED-Circles, each used 3 mixes (1 covering 120°), in smaller venues where we only could setup half-circles, it was much easier to shift the mixes off the screen then to redo the programming.
I was necessary or easier to do it like this in combination with the mapping-controller for the LED-Screen (which was kind of "stupid")
Would you please explain a little more the concept of -No change-.
Referred to Catalyst.
When I turn off the lamp from a moving light, select -Lamp OFF- and that if the default parameter of the lamp does -not change value-
If I release the parameters of the -Clear ALL- lamp will turn back on past time.
Here that I understand the value of "No change"
But do not know, to transfer this concept to a Catalyst Mixer.
Sorry for my ignorance.
Which version did you use in your RHFB?
HighEnd oder Catalyst as manufacturer?
You must use Catalyst, then it should all be fine.
I was in contact with Steve from Highend who takes care of the libs.
I did some screenshots of the actual values from the pulldown menu and send those to him. He checked all values for m329 and they should all be fine he told me.