PDA

View Full Version : Rs232



Mr_P
17-05-2006, 01:03 AM
Been asked for these lots too:

RS232 Codes for various equipment:
BARCO projectors - shutter, power commands
Panasonic projectors - shutter, power commands

!UPDATED!
HEX-DEC-BIN-ASCII conversion cheat sheet
MIDI notes cheat Sheet

Kramer - matrix commands
Procom - matrix commands
Leitch - matrix commands

enjoy

Simon

samsc
17-05-2006, 11:31 AM
thanks simon.

this is very useful

samsc
17-05-2006, 02:54 PM
i added your panasonic codes the the latest build.
Any others you would like?

Mr_P
18-05-2006, 12:22 AM
Actually - Barco Shutter open and close (fast) would be the most useful - say for 2 x projector ID's (1&2).

Im trying to find where I wrote all the other matrix codes as mentioned above - when I find them I'll post them - but there are far too many combinations to include in the Catalyst List - maybe just 2 x examples of each? - check back friday!

S

samsc
18-05-2006, 11:10 AM
please put anything here you want included.
if you are quick it will make it in-
i dont have time to check this - so make sure you give me exactly what you want/need

Spam Butterfly
18-05-2006, 03:32 PM
Barco shutter open and close is a common one I get asked for.

Hugh

samsc
18-05-2006, 03:50 PM
Barco shutter open and close is a common one I get asked for.

Hugh

you have the command string?

Mr_P
19-05-2006, 01:15 AM
Lamp on off and shutter open/close (fast) would be the most useful

Here are codes for 4 x Projector ID's for both Panasonic and Barco:

BARCO CODES:
Shutter OPEN 1
[FE0122420065FF]
Shutter OPEN 2
[FE0222420066FF]
Shutter OPEN 3
[FE0322420067FF]
Shutter OPEN 4
[FE0422420068FF]

Shutter CLOSE 1
[FE0123420066FF]
Shutter CLOSE 2
[FE0223420067FF]
Shutter CLOSE 3
[FE0323420068FF]
Shutter CLOSE 4
[FE0423420069FF]

Note - there is no seperate command for Lamp ON and Lamp
OFF - so the only way to strike/douse lamp is to emulate the
IR remote keypress for 'standby'. Therfore this code will both
strike AND douse the lamp - depending upon the current state
of the lamp. Send code once, it will strike. Send it again later,
it will douse.

IR Standby 1
[FE01300E3FFF]
IR Standby 2
[FE02300E40FF]
IR Standby 3
[FE03300E41FF]
IR Standby 4
[FE04300E42FF]


PANASONIC Codes:
Lamp ON proj 1
[02414430313B504F4E03]
Lamp ON proj 2
[02414430323B504F4E03]
Lamp ON proj 3
[02414430333B504F4E03]
Lamp ON proj 4
[02414430343B504F4E03]

Lamp OFF proj 1
[02414430313B504F4603]
Lamp OFF proj 2
[02414430323B504F4603]
Lamp OFF proj 3
[02414430333B504F4603]
Lamp OFF proj 4
[02414430343B504F4603]

Shutter Open proj 1
[02414430313B4F53483A3003]
Shutter Open proj 2
[02414430323B4F53483A3003]
Shutter Open proj 3
[02414430333B4F53483A3003]
Shutter Open proj 4
[02414430343B4F53483A3003]

Shutter Close proj 1
[02414430313B4F53483A3103]
Shutter Close proj 2
[02414430323B4F53483A3103]
Shutter Close proj 3
[02414430333B4F53483A3103]
Shutter Close proj 4
[02414430343B4F53483A3103]

samsc
19-05-2006, 12:33 PM
i have actually written a custom barco control panel in the past - calculates checksums - does changing of source, and gamma, shutters.
it does a few simple things. its not in the software yet -

if you want to test it i can make it available to you?

---

what projector type or range is the panasonic?
i need somekind of extra label.

Mr_P
20-05-2006, 12:08 AM
Yes - would like to check out your app. My excel spreadsheet does the same - with formulas to add up and calculate the checksum for Barco Codes.

The Barco codes work on the SLM range - I think they are the same for the RLM and XLM, not sure about the new FLM though

Panasonic codes were written for the PT-D7700U-K
According to the documents, it should also work with: PT-D7700U PT-DW7000U PT-DW7700E PT-D7700EK as they share the same software etc.
The codes may also work with the other projectors in the 'large venue' range, but I cant confirm that.

Mr_P
20-05-2006, 01:51 AM
Kramer, Leitch, Procon Matrix RS232 commands on PDF files just updated and added to the 1st message in this thread

(too many options to include in a list though...)

S

samsc
20-05-2006, 08:53 AM
Yes - would like to check out your app. My excel spreadsheet does the same - with formulas to add up and calculate the checksum for Barco Codes.

The Barco codes work on the SLM range - I think they are the same for the RLM and XLM, not sure about the new FLM though


its just another control panel in 'catalyst'. i will put it into a build for you.